該測試儀采用一種新型的特殊電路，對試驗電壓波形進行監測，同時采集電流回路的放電脈沖信號，自動判斷間隙何時放電，鎖存放電瞬間的電壓峰值，同時發出聲光報警信號，以提示試驗者，并迅速切斷試驗電源，保護試品和試驗設備免遭過流損壞。

　　該測試儀集工頻高壓電源、測量、控制系統為一體，濃縮在一個鋁合金箱內，體積小，重量輕，防震耐摔，操作簡單，攜帶方便。該測試儀設有零位、短路保護功能，安全可靠。

　　該測試儀測量系統采用峰值1/√ 2模式，由3位數字式高速電壓表測量，并有記憶功能，直觀清晰。

　　工頻放電自動測試儀的操作步驟

　　1、將測制箱與高壓變用電纜連接;

　　2、將測制箱接地端與高壓變接地端連接后從高壓變接地端接入地網;

　　3、將高壓端用高壓引線連接試品高壓端(高壓引線要有支撐或牽引絕緣物);

　　4、調壓器歸零(調壓器不歸零，不能啟動高壓);

　　5、測試：打開電源開關，待“滴……”音停止后，按一下復位鈕，測量燈(紅)亮，放電燈(綠)滅，電壓表指示回零，測試儀進入待機狀態，調節調壓器開始升壓，當測試儀放電燈亮，發出“滴……”報警聲后，表示試品已放電，測試儀已切斷高壓回路電源，被測數據記憶顯示在電壓表上。至此，試驗完畢，關閉電源開關，更換試品或拆線。

　　7、重復步驟3-5，即可進行下次試驗。